多排陶粒混凝土复合砌块结构优化设计分析

随着我国建筑节能工作的全面推进和不断深化,促进了新型墙体材料的研究和应用.参考相关规范,选取砌块主规格:长×宽×高=390 mm×240 mm×190 mm,根据空心砌块不同孔排数、交错程度和孔洞率,设计12种内部结构不同的空心砌块.通过有限元软件ABAQUS和加权求和法对混凝土自保温空心砌块进行结构优化设计,将优化后的砌块结构浇制成陶粒混凝土空心砌块,空心砌块孔洞由正交试验优化后的泡沫混凝土填充,定量分析不同配比条件下各种材料对泡沫混凝土热工和力学性能影响程度的大小,得到最优配比:水灰比41％,粉煤灰20％,碳酸锂0.16％,聚羧酸减水剂0.075％,微硅粉含量4％和硬质酸钙0.2％,泡沫混凝土的导热系数和抗压强度分别为0.0602 W/(m·K)和5.2 MPa.结合有限元数值模拟和试验研究,制得优化后的陶粒混凝土复合砌块,平均传热系数▉KC3=0.61 W/(m2·K),平均抗压强度10.11 MPa,强度等级达到MU10,同时满足节能65％的要求.     

Wetting,infiltration and interaction behavior of CMAS towards columnar YSZ coatings deposited by plasma spray physical vapor

Thermal barrier coatings (TBCs) produced by electron beam physical vapor deposition (EB-PVD) or plasma spray (PS) usually suffer from molten calcium-magnesium-alumino-silicate (CMAS) attack. In this study, columnar structured YSZ coatings were fabricated by plasma spray physical vapor deposition (PS-PVD). The coatings were CMAS-infiltrated at 1250?°C for short terms (1, 5, 30?min). The wetting and spreading dynamics of CMAS melt on the coating surface was in-situ investigated using a heating microscope. The results indicate that the spreading evolution of CMAS melt can be described in terms of two stages with varied time intervals and spreading velocities. Besides, the PS-PVD columnar coating (～100?μm thick) was fully penetrated by CMAS melt within 1?min. After the CMAS attack for 30?min, the original feathered-YSZ grains (tetragonal phase) in both PS-PVD and EB-PVD coatings were replaced by globular shaped monoclinic ZrO₂ grains in the interaction regions.     

基于三相幅度测量的相控阵天线快速校准方法

提出了一种基于三相幅度测量的相控阵天线快速校准方法。该方法将天线阵列进行分组,利用每种分组在三种配相下的阵面合成场幅度测量值,可解算出各个天线单元的初始幅相值。该方法仅需幅度测量,避免了相位测量误差影响单元幅相值的计算精度,而且所需幅度测量次数仅为(2N+1)次,可显著提高校准时效性。另外,利用分组思想,同时改变多个单元相位,使总辐射场的幅度变化显著,提升校准准确性。仿真结果表明:校准后相位均方根误差为2.2°,幅度均方根误差为0.2 dB。     

Decoder side information generation techniques in Wyner-Ziv video coding: a review

Multimedia Tools and Applications - In Wyner-Ziv (WZ) video coding, decoder side information (SI) takes a key role in a WZ video codec among other building blocks. In this paper, we review the...     

Microwave drying performance of lignite with the assistance of biomass-derived char

Microwave lignite drying with assistance of biomass-derived char was addressed and effect of bio-char on drying rate and energy consumption was investigated in this work. Effective diffusion coefficient and activation energy for the drying process were also analyzed. The results indicated the drying process was largely dependent on the variation of sample temperature. Bio-char originated from pine wood was most favorable for lignite drying, considering its better promoting effect and advanced security. There existed an optimal bio-char addition ratio for drying process at different power. The corresponding optimal ratio was 10% at 231?W and 15% at 385?W, at which the biggest drying rate and the least energy consumption were reached. It was compared lignite drying initiated at 385?W was better for energy conservation. Effective diffusivity was improved and activation energy was simultaneously reduced, with the addition of bio-char. The minimum activation energy was 15.54?W?·?g^?1, which was gained at bio-char addition ratio of 10%. The results revealed the effect of bio-char on depressing activation energy could rival that of metal-based additives. The drying process with assistance of microwave and bio-char could present technical and economical benefits on lignite upgrading.     

MC脉冲粗煤泥分选机在老石旦洗煤厂的应用

为降低老石旦洗煤厂的粗精煤灰分,在对粗煤泥性质分析的基础上,采用MC脉冲粗煤泥分选机对其进行分选。介绍了该分选机的结构、工作原理、技术特点、技术参数,并分析了其在老石旦洗煤厂的应用情况。生产实践表明:MC脉冲粗煤泥分选机不但可降低粗精煤灰分,而且可提高其产率。该分选机投入使用后粗精煤灰分下降3个百分点,总精煤产率提高0.5个百分点,达到了降灰的目的。     

离子侵蚀对再生混凝土多重界面区微观形貌影响

为了研究离子侵蚀对再生混凝土多重界面过渡区的影响,借助SEM和EDS,以Ca元素和Si元素为特征元素进行面扫描,实现了对骨料和砂浆基体的区分,发现了经NaCl溶液和Na2SO4溶液浸泡60 d后的再生混凝土界面过渡区趋于疏松;以S元素和Cl元素为示踪元素,观察到其在界面区的富集,证明了界面过渡区是离子侵蚀的主要通道;浸泡60 d后界面区显微硬度分别下降约70％和20％,界面过渡区宽度分别增加约50％和20％.研究实现了对离子侵蚀后再生混凝土界面过渡区位置和范围的界定,且表现出与显微硬度结果的一致性.     

基于用户体验的产品包装设计探究

在经济繁荣发展的今天,人们对产品包装的需求已经不仅仅是功能上所完成的,用户与包装互动过程中综合感受才是重点。文章通过案例分析和研究,对现代产品包装设计中本能层次、行为层次、反思层次的体验设计进行分析。基于用户体验的产品包装设计,将使产品包装更为合理、人性化、获得更加愉悦的心情和美好回忆,同时促进销售且提升品牌文化及其附加价值。     

一种汽车顶盖抗雪压动态仿真分析方法

目前顶盖雪压静态仿真分析方法的雪压计算值与测试值存在偏差,并且不能反映顶盖实际变形的位置和整体变形模式。为改进静态仿真分析方法,提出一种非线性显式计算的动态仿真分析方法,并以某乘用车为例,通过试验验证了其可靠性及有效性,为顶盖的研发设计提供了参考。